refactor(doorbell-touch): remove entire sketch for rebuild

This commit is contained in:
2026-02-16 21:13:31 -08:00
parent 7085bfff04
commit b47993b29a
16 changed files with 0 additions and 2275 deletions

View File

@@ -1,50 +0,0 @@
#pragma once
// ═══════════════════════════════════════════════════════════════════
// Board: E32R35T — ESP32-WROOM-32E + 3.5" ST7796S SPI + XPT2046
// ═══════════════════════════════════════════════════════════════════
#define BOARD_NAME "E32R35T"
// ── Display ─────────────────────────────────────────────────────
#define SCREEN_WIDTH 480
#define SCREEN_HEIGHT 320
#define DISPLAY_ROTATION 1
// ── Driver selection ────────────────────────────────────────────
#define USE_TFT_ESPI 1
#define USE_ARDUINO_GFX 0
#define USE_TOUCH_XPT2046 1
#define USE_TOUCH_GT911 0
// ── Hardware capabilities ───────────────────────────────────────
#define HAS_PSRAM 0
// ── LCD (HSPI) ──────────────────────────────────────────────────
#define PIN_LCD_CS 15
#define PIN_LCD_DC 2
#define PIN_LCD_MOSI 13
#define PIN_LCD_SCLK 14
#define PIN_LCD_MISO 12
#define PIN_LCD_BL 27
// ── Touch (XPT2046, shares HSPI) ───────────────────────────────
#define PIN_TOUCH_CS 33
#define PIN_TOUCH_IRQ 36
// ── SD Card (VSPI — for future use) ────────────────────────────
#define PIN_SD_CS 5
#define PIN_SD_MOSI 23
#define PIN_SD_SCLK 18
#define PIN_SD_MISO 19
// ── RGB LED (active low) ───────────────────────────────────────
#define PIN_LED_RED 22
#define PIN_LED_GREEN 16
#define PIN_LED_BLUE 17
// ── Audio ───────────────────────────────────────────────────────
#define PIN_AUDIO_EN 4
#define PIN_AUDIO_DAC 26
// ── Battery ADC ─────────────────────────────────────────────────
#define PIN_BAT_ADC 34

View File

@@ -1,73 +0,0 @@
#pragma once
// ═══════════════════════════════════════════════════════════════════
// Board: Waveshare ESP32-S3 Touch LCD 4.3"
// 800x480 RGB parallel + GT911 capacitive touch
//
// NOTE: Pin assignments are typical for this board revision.
// Verify against your specific board's schematic.
// The Arduino board variant 'waveshare_esp32_s3_touch_lcd_43'
// may override some of these via its pins_arduino.h.
// ═══════════════════════════════════════════════════════════════════
#define BOARD_NAME "WS_S3_43"
// ── Display ─────────────────────────────────────────────────────
#define SCREEN_WIDTH 800
#define SCREEN_HEIGHT 480
#define DISPLAY_ROTATION 0 // native landscape
// ── Driver selection ────────────────────────────────────────────
#define USE_TFT_ESPI 0
#define USE_ARDUINO_GFX 1
#define USE_TOUCH_XPT2046 0
#define USE_TOUCH_GT911 1
// ── Hardware capabilities ───────────────────────────────────────
#define HAS_PSRAM 1
// ── Backlight ───────────────────────────────────────────────────
#define PIN_LCD_BL 2
// ── GT911 I2C touch controller ──────────────────────────────────
#define TOUCH_SDA 17
#define TOUCH_SCL 18
#define TOUCH_INT -1
#define TOUCH_RST 38
// ── RGB LCD data pins (ESP32-S3 LCD_CAM peripheral) ─────────────
// Adjust if your board revision differs
#define LCD_DE 40
#define LCD_VSYNC 41
#define LCD_HSYNC 39
#define LCD_PCLK 42
#define LCD_R0 45
#define LCD_R1 48
#define LCD_R2 47
#define LCD_R3 21
#define LCD_R4 14
#define LCD_G0 5
#define LCD_G1 6
#define LCD_G2 7
#define LCD_G3 15
#define LCD_G4 16
#define LCD_G5 4
#define LCD_B0 8
#define LCD_B1 3
#define LCD_B2 46
#define LCD_B3 9
#define LCD_B4 1
// ── Peripherals not present on this board ───────────────────────
// These are left undefined intentionally. Code that uses them
// should guard with #ifdef PIN_LED_RED etc.
// Uncomment and set values if your carrier board adds them.
//
// #define PIN_LED_RED -1
// #define PIN_LED_GREEN -1
// #define PIN_LED_BLUE -1
// #define PIN_AUDIO_EN -1
// #define PIN_AUDIO_DAC -1
// #define PIN_BAT_ADC -1
// #define PIN_SD_CS -1
// #define PIN_TOUCH_CS -1
// #define PIN_TOUCH_IRQ -1